Brass, gold & metallic legs

Brass Furniture Legs That Fit Over Your Existing Legs

Give your furniture a brass, gold or silver look while adding height. These legs slide over the legs you already have with a snug 2-inch deep pocket, and are printed in a satin metallic finish that pairs with brass, gold and chrome hardware.

Square and round brass furniture legs with a 2-inch deep pocket holding light wooden furniture legs

Cut to your measurement, to two decimal places.

Made to order · ships in 3–5 business days.

Indoor use only, keep out of direct sunlight and extreme temperatures.

Details

A metallic look without metal

The finish is a satin metallic sheen built into the material, not paint or plating, so it won't chip or peel. Fine layer lines are part of the look and read like brushed metal. Choose Brass, Gold, Rose Gold, White Gold, Silver or Copper.

Nothing is screwed or glued. Your existing sofa, bed, dresser, cabinet or table leg slides 2 inches down into the pocket and is held on every side, so you can raise furniture and update its look without tools, and take the legs off again later.

How to size brass furniture legs

The size you order is the pocket, the opening your leg slides into. Measure the widest part of the existing leg within its bottom 2 inches and add about 0.05 inch. A 1.70 inch leg gets a 1.75 inch pocket. If the leg is not perfectly square, straight or uniform, add 0.10 to 0.15 inch so it slides in easily.

The height you pick is how much your furniture is lifted. Because the pocket is 2 inches deep, the new leg also rises 2 inches up around your old one. Taller, narrower legs are less stable, so keeping the pocket at least as wide as the lift is the steadier choice. Text a photo of the leg next to a ruler to 860-856-3633 if you are unsure.

Configurator

Build your brass furniture legs

We've prefilled a typical size for this kind of furniture, change it to your own measurements, then enter the total weight the legs will carry.

1. Pocket size

The opening your leg slides into

Choose the one-inch range for the pocket, the opening your existing leg slides 2" down into. These are a snug fit: if your leg measures 1.70", the pocket is 1.75", so pick 1–2".

2. Height

How far you're lifting

Choose the one-inch range for the lift you want.

With a 1–2" pocket, heights above 6" are grayed out. A narrow footprint lifted that high gets tip-prone, step up a pocket size to unlock taller legs.

3. Exact dimensions

Pocket size and lift

Decimals welcome, enter your exact number. Width and depth are the pocket, the opening your leg slides into, not the leg itself. Height is how much your furniture is lifted.

Snug fit: add about 0.05" to your measured leg. A 1.70" leg gets a 1.75" pocket. If the leg isn't perfectly square or straight, add 0.10" to 0.15" instead so it slides in easily. The pocket is 2" deep, so the new leg also rises 2" up around your old one.

Not sure how to measure? Tap for a quick guide
  1. Measure the bottom of the leg where it touches the floor, side to side (width) and front to back (depth).
  2. Measure the widest part within the bottom 2" (that whole section sits in the pocket) and add 0.05". A 1.70" leg becomes 1.75".
  3. For height, pick how much lift you want. Under 3" is the most popular for beds.
  4. Still unsure? Text a photo of the leg next to a ruler to 860-856-3633 and I'll tell you the size to order.

Starting size, enter your own measurements.

in

Opening size, including 0.05" clearance

in

Opening size, including 0.05" clearance

in

Within 1–2"

Rectangular leg? Choose the range for your longer opening dimension. The shorter side can be below that range, down to 0.5". Add 0.05"to each measured leg dimension before entering it.

Total weight: 200 lbs (typical chair or desk). Heavier? Change this.

Include the furniture plus anything (or anyone) on it, a bed frame, mattress and the people sleeping on it, for example. This helps us build safely.

lbs

4. Metallic color

No extra cost

Every metallic finish is the same price, pick the one that suits the room.

Metallic

Metallic legs have a subtle sparkle in the finish. Color may vary slightly due to computer image.

5. Custom shapes & notesOptional · show

Any shape is available: circles, ovals, L-shapes, triangles, tapered or angled legs. Choose the base range that covers the widest part of the leg, then add the shape and its dimensions in the notes below.

0/600 characters

Total · 4 legs

$141.00

FAQ

Brass furniture legs questions

No. They are 3D printed from a metallic PLA with a satin brass, gold, silver or copper sheen built into the material. There is no paint or plating to chip.