How to Choose the Right Riser Height for Your Furniture

The right riser height is the one that fixes a specific problem: a bed you have to climb out of, a sofa that is hard to stand up from, a desk that makes you hunch, or a gap under the frame that is too short for storage bins. Start with that problem, measure the height you have now and the height you want, and the riser is the difference between the two. Because we build ours to the size you enter, you are never forced to round to a pre-set height such as 3, 5 or 8 inches.
This guide shows you what to measure, how to turn the measurements into a riser height for each type of furniture, and where people most often get it wrong.
TL;DR
- Riser height = the height you want minus the height you have. Measure both with a tape, in inches, to the nearest 1/16 inch.
- For beds, sofas and chairs, aim the seat or mattress edge at about knee height so standing up takes less effort.
- For desks, set the work surface so your elbows sit at about 90 degrees with your shoulders relaxed. Test it with your own chair and keyboard.
- For storage, riser height = the tallest container + about 1/2 inch of slack, minus the clearance you already have.
- Heavier loads and taller risers call for extra stability. Tell us the load when you order and we can build for it.
Table of Contents
- Start with the problem, not the number
- What to measure before you pick a height
- How to choose riser height by furniture type
- Planning for hidden storage
- Load, stability and finish
- Quick reference: height targets and the formula for each
- Common mistakes when choosing riser height
- Order a riser at the height you worked out
- Our view on riser height
- If you were looking for stair riser height
- FAQ
- Sources
Start with the problem, not the number
People usually search for a riser height because a number was suggested to them: “get 6-inch risers.” That number may or may not fit your room. The better order is:
- Name the problem. Is the furniture too low, or do you want space underneath it, or both?
- Measure what you have today.
- Decide the target.
- Subtract.
The reason this matters is that pre-set risers come in a handful of sizes. If your target is 4.25 inches and the nearest option is 5, the furniture ends up too high, too tall for the headboard or too close to a window sill. A custom riser removes that compromise, since you can specify dimensions down to the hundredth of an inch in our configurator.
What to measure before you pick a height
A few minutes with a tape measure saves a return.
Current height. For a bed, measure from the floor to the top of the mattress. For a sofa or chair, from the floor to the top of the seat cushion, pressed down lightly the way it sits when you do. For a desk or table, from the floor to the work surface.
Clearance under the frame. Measure from the floor to the lowest part of the frame, rail or slat support. This is the space your storage, robot vacuum or cables must fit into, and it is the number that grows when you add risers.
Leg shape and size. Round, square, tapered, angled or splayed legs each need a different socket or fit. Our guides on how to measure furniture legs and on risers for tapered and mid-century legs walk through the exact points to measure. Take the leg size at the spot where the riser will grip it, not at the widest or narrowest end.
Your own body. Knee height (floor to the top of your knee while seated, shoes on) and, for desks, elbow height (floor to the underside of your elbow while seated with forearms level). Ask someone to help, or use a wall and a pencil.
Limits in the room. A headboard that is attached to the wall, a window ledge, a ceiling fan above a bunk, cabinets above a desk or a doorframe a rolling piece must pass through can all cap how tall you can go.
How to choose riser height by furniture type
Beds
Bed height is a comfort and a storage decision at the same time.
For comfort, a common rule of thumb is that the top of the mattress should sit near your knee height, so your feet rest flat on the floor when you sit on the edge and your legs do the work of standing. If you are tall, have stiff knees or hips, or have a low platform frame, the bed may sit several inches below that line. The gap is your riser height.
For storage, work from the container instead. Take the tallest bin, drawer or suitcase you want underneath, add about 1/2 inch so it slides without scraping, and subtract the clearance you already have.
Worked example: your frame leaves 4 inches under the rails. You want 7-inch storage bins to slide in. 7 + 0.5 = 7.5 inches needed, and 7.5 - 4 = 3.5 inches of riser. The bed also rises 3.5 inches, so check that the new mattress height is still comfortable and that it does not meet the knee-height target by overshooting it. If the two goals conflict, comfort usually wins, and you can choose a shorter bin instead.
Beds carry the most weight of any furniture, often two people plus a mattress. Check the load before you finalize, and look at our bed risers and heavy duty risers for taller or heavier setups. Use the same riser height under every leg, including any center support legs, so the frame stays level.

Sofas and chairs
The test for a sofa is simple: sit on the front edge of the cushion. Your hips should sit at or slightly above your knees, and you should be able to stand without rocking forward or pushing hard with your arms. A seat that is too low is the usual reason people struggle to get up from a couch, and it is especially noticeable for tall users or anyone with sore knees or hips.
Measure the seat height as you sit on it, since a soft cushion compresses. Then measure your knee height. If the cushion top is 16 inches and your knee height is 19, a riser of about 2.5 to 3 inches brings you to the right range, with the extra compression of the cushion as your margin.
Things that change the answer:
- Cushion softness. A deep, soft cushion sinks. Plan the height for the compressed seat, not the cushion at rest.
- Arm and back proportions. Raising a sofa raises its arms and back too. Check that the arm height still suits you and that the sofa clears any window sill behind it.
- Sleepers and sectionals. Raise every leg by the same amount, including the center legs, so sections stay aligned.
Our couch and sofa risers are made to the leg size you give us, so a tapered or angled leg does not have to be forced into a one-size cup. Dining and desk chairs follow the same logic, and our chair risers are built for it.
Desks
Desk height is less about knees and more about elbows. When you sit with your upper arms relaxed at your sides, your forearms should be about level with the floor and your wrists straight while typing. The surface you type on, whether the desktop or a keyboard tray, should be at that elbow height.
Worked example: you sit in your chair with feet flat and measure 31 inches from the floor to the underside of your elbow. Your desk top is 29 inches and your keyboard sits on it. The keyboard is about 1 inch thick, so the typing surface is about 30 inches. You need about 1 inch more, so the riser height is 1 inch. If you instead lower your chair to match a low desk, your feet may no longer reach the floor, which is why raising the desk is often the better fix for tall users.
A few practical notes:
- Measure with the chair and keyboard you actually use.
- If you use a monitor, raise it separately so the top of the screen is at or slightly below eye level. A desk riser does not do that job for you.
- Check knee and thigh clearance under the desk. A taller desk gives more room, which is usually a plus.
- Use the same height at each leg, and add stability for a heavy desk with a large monitor setup or drawers.
See our desk risers for the options.
Dining tables, coffee tables and other tables
Most dining tables are made to be a certain height for standard chairs. If you are taller than average, if your chairs are higher, or if you want a counter-height table for standing or stools, a table riser is a way to get there without replacing the table. Measure the table surface now, then measure the target. For a dining set, the gap between seat and table top should leave room for your thighs and still let your forearms rest comfortably on the surface. That is why you should measure your chairs before you decide how much to raise the table.

When you raise a table, you change which chairs go with it. If you raise the table by 6 inches, you will probably need stools or taller chairs. Our guide to dining table risers explains how to get to counter or comfort height, and the table risers page lets you configure the size.
For a coffee table that is too low to reach from a sofa, the same idea applies: match the top of the table to a point a few inches below the seat edge, so you are not leaning far forward to reach it.
Planning for hidden storage
Risers do double duty when the extra height becomes storage space. This is a major reason apartment dwellers choose them, since the floor under a bed or sofa is often the largest unused space in a small home.
The formula again:
Riser height = tallest item + 1/2 inch of slack - existing clearance.
A few things to include in the measurement:
- The container and its lid. Measure the container with the lid on, not the empty tub.
- A cross rail or slat support. The lowest part of the frame sets your clearance, not the average. Measure at the lowest point.
- Carpet. Thick carpet or a rug can eat into your clearance. Measure from the top of the floor surface where the container will actually sit.
- A robot vacuum. If you want a robot vacuum to pass underneath, measure its height and add some margin. Our guide to furniture risers for a Roomba covers height, fit and safety.
Load, stability and finish
Height is only part of the choice. Two other decisions affect how the riser performs.
Load. Think about what sits on the furniture, not just the furniture. A bed with two adults, a sectional with several people, a desk with a heavy monitor and drawers, or a bookshelf full of books all put weight on the legs. For heavier uses, our heavy duty furniture risers are designed to carry more, and the extra stability option is $5.00 each, one-off. Taller risers have more leverage working against them, so the taller you go, the more worthwhile it is to specify extra stability for something heavy or tall.
Finish. The riser can blend in or stand out. The options are wood tones, solid colors, metallic finishes, and a wood grain texture at $5.00 each, one-off. See colored risers and metallic risers if you want them to match the furniture or the room. Interior designers often match the riser to the leg or the floor so that the added height reads as part of the piece.
Quick reference: height targets and the formula for each
| Furniture | What to measure | Target | Riser height |
|---|---|---|---|
| Bed (comfort) | Floor to top of mattress, your knee height | Mattress top near knee height | Knee height minus mattress height |
| Bed (storage) | Tallest container, clearance under frame | Container + 1/2 inch of slack | Needed clearance minus current clearance |
| Sofa or chair | Compressed seat height, your knee height | Seat at or a little above knee height | Knee height minus compressed seat height |
| Desk | Elbow height seated, typing surface height | Elbows at about 90 degrees | Elbow height minus typing surface height |
| Dining or coffee table | Table height, chair seat height | Comfortable reach for the seating you use | Target height minus current height |
Common mistakes when choosing riser height
- Measuring the cushion at rest. A soft sofa seat compresses by an inch or more. Measure when it is loaded.
- Forgetting that everything else rises too. The headboard, the sofa back and the table top all go up with the legs. Check what is nearby.
- Mixing heights. Every leg gets the same height, including center and support legs, or the piece will rock or twist.
- Ignoring the leg shape. A round cup on a tapered leg will wobble. The riser needs to fit the leg you have.
- Overshooting. More height is not better. A bed that is too high is as awkward as one that is too low, and a taller riser needs more stability.
- Skipping the final check. Before you order, put books, blocks or a stack of boards under one leg at the planned height and sit or stand at the furniture. A quick trial catches a height that looks right on paper but feels wrong.
Order a riser at the height you worked out
Once you have your number, our configurator lets you enter it exactly, choose the leg shape, pick a color or finish and see the cost update as you change each option. Start from the custom riser page, or go straight to the page for your piece: bed, sofa, desk or chair. If your furniture has unusual feet, we can build for round, angled and irregular legs as well as standard ones.

If you want to see what a pair of legs would look like with a taller or shorter riser, change the height in the configurator and the price updates immediately, so you can compare a few options before you decide.
Our view on riser height
We think the biggest problem with furniture risers is not the product, it is the menu. A shopper needs 4.25 inches, finds 3 or 5, and settles. Then the bed is a little too high, or the sofa is still a little too low, and the fix was supposed to be simple.
That is why we build to the size you enter, down to the hundredth of an inch. A height is not a category. It is the difference between the furniture you have and the way you want to use it, and that difference should be the number on the order.
The same goes for the leg. Round, angled and irregular legs are common, and a riser should fit them, not be forced onto them. We also think extra stability and a finish that matches the room belong in the same order, which is why they are options in the configurator and the price updates as you choose.
Measure the height you have, decide the height you want, subtract, and order that number.
Harris
If you were looking for stair riser height
Stair risers are a different subject, and code limits apply to them. If you are building or checking stairs in the United States, the Institute of Builders gives the IBC limits and the method: residential stairs allow a maximum 7.75-inch rise with a minimum 10-inch tread, and you divide the total rise by the number of steps to get the exact riser height. Local code and your building department decide what applies to your house.
FAQ
What is the best riser height for a bed?
It depends on your goal. For comfort, aim for a mattress top near your knee height. For storage, take your tallest container, add about 1/2 inch and subtract the clearance you already have. We build to the exact size, so you do not have to round to a standard option.
How tall should risers be for a sofa that is hard to get out of?
Measure the seat height while you sit on it, then measure your knee height. The difference is a good starting point for the riser. Many people land in the range of a few inches, but the right number depends on your legs, the cushion and how much the seat compresses.
Can I use different riser heights under different legs?
It is better to use the same height on every leg, including center support legs. Mixed heights tilt the piece and put uneven load on the legs. If your floor is uneven, tell us about it when you plan the order.
How do I choose a riser height for a desk?
Sit in your usual chair with your feet flat and measure to the underside of your elbow. Your typing surface should be near that height, so subtract the current surface height, including a keyboard if it sits on top, and the result is your riser height.
Do taller risers need extra stability?
Taller risers have more leverage working against them, and heavy furniture adds load. You can add extra stability for $5.00 each, one-off, and our heavy duty risers are made for higher loads.