How to Raise Your Bed to Fit Drawers Underneath

To raise a bed for drawers, subtract the clearance your bed already has from the height of the drawers you want, add about an inch so they slide freely, and lift the frame by that difference with risers cut to your exact leg shape. Then check that the new mattress height still lets you sit down and stand up comfortably. This guide walks through each step. If you were searching for a raised garden bed with drawers, this page is about bedroom furniture, so you will want a woodworking guide for planters instead.
Our custom bed risers are made to the measurements you enter, so the lift is exactly what your drawers need, not the nearest pre-set size.
TL;DR
- Lift needed = drawer height + about 1 inch of working room − the clearance under your bed today.
- Most standard frames leave roughly 6 to 9 inches under the bed, which is why deeper drawers usually mean raising the frame.
- Keep the top of the mattress in a range that lets you sit with feet flat on the floor: about 20 to 23 inches is the figure given for accessibility.
- Risers must fit your leg shape (round, tapered, angled) and carry the load of the bed and everyone in it.
- We make risers to the hundredth of an inch from a configurator that updates the cost as you choose.
Table of Contents
- Why raising the bed beats squeezing in smaller boxes
- Step 1: Decide which drawers you want to fit
- Step 2: Measure the clearance you have now
- Step 3: Do the math
- Step 4: Check the new mattress height
- Step 5: Match the riser to your legs
- Step 6: Plan for the load
- Step 7: Choose a finish that suits the room
- Step 8: Order, install, and load the drawers
- Our view on raising a bed for drawers
- Get risers cut to your bed
- FAQ
- Sources
Why raising the bed beats squeezing in smaller boxes
Under-bed space is the biggest unused storage in most bedrooms, especially in apartments where closets are small. The problem is height. The flat boxes sold for the purpose are built around the low clearance most frames leave: one under-bed container review describes a 6-inch-tall, 28-quart box as holding about one dresser drawer’s worth. That is useful for flat items. It will not hold a folded winter comforter, boots, or a real rolling drawer unit.
Raising the frame changes what is possible. A few extra inches turns a place for seasonal sheets into a place for drawers you open every day. And because the risers sit under the legs, you keep the bed you already own, with its headboard, rails and slats, instead of replacing it.
Step 1: Decide which drawers you want to fit
Start with the storage, not the bed. Write down what will live under there and how it will move.
- Flat under-bed boxes: usually 6 to 7 inches tall.
- Rolling drawers or crates: add the wheel height to the box height. Measure the whole unit, wheels included.
- A drawer unit or chest of drawers: measure from the floor to the top of the unit. Many are taller than any standard frame clearance.
- Built-in drawers you will build yourself: measure the finished height including the slides and the face panel.
If you have not bought the drawers yet, this is the better order. You can choose the drawers you like and then set the bed height to suit, instead of buying whatever fits under a bed that is already too low.
Step 2: Measure the clearance you have now
Measure under the lowest part of the frame, not the legs. Side rails, center support beams, and cross slats often hang lower than the rest of the frame, and they set the real limit.
- Remove the bedding and anything stored under the bed.
- Place a hard-edged tape measure on the floor and read up to the underside of the lowest rail or beam.
- Take the reading in at least three places: near the head, the middle, and the foot. Floors and frames are rarely perfectly level.
- Note the thickness of any rug the drawers will roll over. A thick rug takes clearance away.
- Write down the smallest number. That is your clearance.
Also measure the width and length of the open space between the legs and under the center beam. Raising the bed gives you height, but a center support leg or a cross beam still blocks drawers that are too wide.
Step 3: Do the math
The formula is simple:
Lift needed = drawer height + 1 inch of working room − current clearance
The extra inch is our rule of thumb. It lets a drawer slide in and out without catching the rail, and it covers the lip of a rug.
A worked example. Your frame leaves 6 inches of clearance and you want a rolling drawer unit that measures 11 inches tall with its wheels.
- 11 + 1 = 12 inches needed under the frame
- 12 − 6 = 6 inches of lift
Now check the second number that matters, the height of the mattress top, which the next step covers.
Step 4: Check the new mattress height
Every inch you add under the bed is an inch added to the sleeping surface. For most adults that matters more than the storage does.
The National Council on Aging says that, for most people, the top of the mattress should sit about 20 to 23 inches from the floor. It also gives a simple test: you should be able to sit on the edge with both feet flat on the floor and your knees bent at about 90 degrees. A bed that is too high makes it hard to plant your feet, and one that is too low takes extra effort to stand from.
Here is how that plays out with the 6-inch lift from the example:
| Mattress top today | After a 6 in lift | Sit-and-stand check |
|---|---|---|
| 16 in | 22 in | Inside the 20 to 23 in range |
| 19 in | 25 in | Above the range; stand-up test needed |
| 22 in | 28 in | Well above the range for most people |
If your new height lands above the range, you have three options that still keep the drawers: choose drawers a little lower, use a thinner mattress or foundation, or accept a taller bed after trying the sit test at that height. Taller people often find a higher bed more comfortable, because their feet reach the floor at a greater height. Sit on the edge with a stack of books or boards under each leg to test before you commit.
If the bed is too low today, which is common with platform beds and older frames, a lift that brings you into the range helps with standing up as well as storage. That is the best case for risers: you gain both comfort and drawer space from the same inches.
For a deeper look at lift amounts, see our guide on how much lift under-bed storage really needs, and our overview of ways to raise bed height if you are weighing methods.

Step 5: Match the riser to your legs
This is where most do-it-yourself lifts go wrong. A riser is a cup or block the leg sits in. If the cup is the wrong size or shape for the leg, the bed can wobble, shift, or tip. Check your leg type first.
- Square or rectangular legs: the easiest to fit, but still need a pocket sized to the leg, not an approximate one.
- Round legs: need a round seat. A square cup around a round leg leaves it free to rotate and walk.
- Tapered or mid-century legs: the leg is narrower at the bottom, so a straight-sided cup cannot hold it snugly. See our guide on getting a snug fit on tapered and mid-century legs.
- Angled or splayed legs: the foot sits on a slant, so the riser has to account for the angle.
- Irregular legs: bun feet, turned legs, and anything oddly shaped need a riser made around that shape.
Standard risers come in pre-set sizes and may not fit irregular legs. That is the reason we build ours to your measurements. You enter the dimensions of your leg down to the hundredth of an inch, and the riser is made to that size. It supports round, angled, irregular, and standard legs. If your bed has no suitable legs at all, or you want to replace them with something taller, we also make custom furniture legs.
Measure each leg’s width, depth, and shape at the point where the riser will meet it. Do this for every leg. Beds are not always symmetrical, and a center support leg can be a different size from the corners.

Step 6: Plan for the load
A bed frame carries the mattress, the bedding, and the people on it, usually concentrated on four to six legs. Add drawers underneath and you will be tempted to stack things near the legs, but risers do not carry the drawers. They only carry the bed. Still, a taller bed has a higher center of gravity, so a loose or undersized riser is a bigger risk at 8 inches than at 2.
For couples, larger mattresses, or heavy frames, choose a reinforced option. Our heavy duty furniture risers are made to order for higher loads, and the extra stability option is $5.00 one-off per each riser. Check your frame’s rated capacity in its manual and keep the total weight of the mattress and sleepers in mind when picking.
A few more habits keep a raised bed stable:
- Put the bed on a level floor, and check it again after the first week.
- Make sure every leg is seated fully in its pocket.
- If the bed has a center support leg, raise it by the same amount as the corner legs.
- Push the bed against a wall at the head if you can, which reduces sliding.
Step 7: Choose a finish that suits the room
Risers under a bed are mostly hidden by a bed skirt or the shadow of the frame, but not always. On a platform or open-leg bed they are a visible part of the design. That is where finish options matter, especially for decorators matching a room.
We offer wood tones, solid colors, metallic finishes, and a wood grain texture. The wood grain texture is $5.00 one-off per each riser. If you want the risers to blend into dark legs, a colored riser in a close tone works. For a statement look with brass or metal legs, see our metallic options or brass furniture legs.
Step 8: Order, install, and load the drawers
Ordering is done in the configurator on our site. You pick the furniture type, enter the leg dimensions and the height you calculated, add any finish or stability options, and the cost updates as you choose. Riser prices are not listed in advance because they depend on your dimensions, so the configurator is where you see the total.
When the risers arrive:
- Strip the bed and have a second person help. Do not lift one end alone.
- Raise one corner at a time, set the riser under the leg, and lower the leg into it.
- Repeat for every leg, including the center support.
- Press on each corner to check it does not rock.
- Slide in the drawers and test the clearance across the whole length.
- Make the bed and run the sit-and-stand test one more time.
Do this before you load the drawers, not after. If something needs adjusting, you want the space empty.
Our view on raising a bed for drawers
Most people come to us with a number in mind, usually “I want it three inches higher.” The better question is “what do I want to put under there?” Start from the drawers, work out the lift, and check it against how it feels to sit on the edge of the bed. That order gives you storage you use and a bed you can get out of.
The other thing we see in how furniture is built is that legs vary far more than risers do. Round, tapered, angled, and turned legs are everywhere, yet pre-set risers assume a plain square foot. We built our configurator around exact measurements because a fit that is off by a fraction of an inch is a fit that moves. Entering your leg size to the hundredth of an inch, seeing the price update as you go, and choosing reinforcement for heavy beds means the riser is made for your bed, not the average one.
Raising a bed is a small change with a big result: more storage, and a sleeping surface at the height that suits you.
Harris
Get risers cut to your bed
If you have your drawer height and leg measurements, you can build your order now. Our bed risers are made to the dimensions you specify, with wood tone, color, metallic, and wood grain finishes, and an extra stability option for heavier loads. The configurator shows the cost as you choose.

For couches and sofas that need the same treatment, see our couch and sofa risers. To start from the full range, go to custom furniture risers.
FAQ
How high should I raise my bed for under-bed drawers?
Raise it by the drawer height plus about an inch, minus the clearance you have now. Most standard frames leave 6 to 9 inches, so a 6-inch box may need no lift at all, while an 11-inch rolling unit on a 6-inch frame needs about 6 inches. Always check the resulting mattress height as well.
What is a good mattress height after raising the bed?
The National Council on Aging gives about 20 to 23 inches from floor to mattress top as a height that suits most people. The practical test is sitting on the edge with feet flat and knees at about 90 degrees. If you have arthritis, balance problems, or past falls, talk to your doctor or physical therapist about the right bed height for you.
Will risers work on round or tapered bed legs?
They will if they are made for that leg shape. A riser with a straight square cup will not hold a tapered or round leg snugly. We make ours to your measurements, including for round, angled, and irregular legs, so each one seats the leg properly.
Can I raise a heavy bed or one that two people use?
Yes, with risers made for the load. Choose the extra stability option, which is $5.00 one-off per each riser, or our heavy duty range, and check the frame’s own weight rating. Seat every leg fully, including any center support, and check the bed is level after the first week.
Sources
- The Best Under-Bed Storage Containers
- Bedroom Safety for Older Adults: How to Prevent Falls at Home, NCOA